SQUARE WAVE GENERATOR MODULES

ECL-100K-SWGM-XX

100K ECL Square Wave Generator Module

- ECL 100K input and outputs
- Output wavetrain can be started in sync with random events
- 16-pin DIP package (.280 high)
- Available in frequencies from 50 MHz to 250 MHz
- Output frequencies controlled to within ± 2%
- High fan-out capacity

DESIGN NOTES

The "DIP Series" Gated Square Wave Generator Modules developed by Engineered Components Company have been designed to provide an ECL 100K square wave output at frequencies from 50 MHz to 250 MHz. These generators are both keyable and synchronizable, producing a continuous output train as long as a zero (low) is maintained at the enable input. As long as the enable input is a "1" (high), the output will be a constant "1" (high). Whenever the enable input goes low, the output wavetrain will start in the same sequence with the first low appearing one-half cycle after trigger, and the first positive edge occuring after the period of one cycle. (Note: The output buffer will add one propagation delay to all times). This feature allows the initiation of a timing wavetrain with the origin in synchronization with another event.

These Square Wave Generator Modules are of hybrid construction utilizing the proven technologies of active integrated circuitry and of passive networks utilizing capacitive, inductive and resistive elements. The ICs utilized in these modules are burned-in to Level B of MIL-STD-883 to ensure a high MTBF. The MTBF on these modules, when calculated per MIL-HDBK-217 for a 50°C ground fixed environment, is in excess of 3.3 million hours.

The ECL-100K-SWGM is offered in twenty-six (26) frequencies. Output frequencies are controlled to within ± 2% and have a temperature coefficient of less than +200 ppm/°C over the operating temperature range of 0 to +85°C.

These "DIP Series" modules are packaged in a 16-pin DIP housing, molded of flame-proof Diallyl Phthalate per ASTM D 5948, Type SDG-F, and are fully encapsulated in epoxy resin. Leads meet the solderability requirements of MIL-STD-202, Method 208. Corner standoffs on the housing provide positive stand off from the printed circuit board to permit solder-fillet formation and flush cleaning of solder-flux residues for improved reliability.

Marking consists of manufacturer's name, logo (EC²), part number, terminal identification and date code of manufacture. All marking is applied by silk screen process using white epoxy paint in accordance with MIL-STD-130, to meet the permanency of identification required by MIL-STD-202, Method 215.

TEST CONDITIONS

1. All measurements are made at 25°C.
2. Vee supply voltage is maintained at -4.5V DC.
3. All units are tested using a standard open emitter ECL 100K gate at the input. The input and output utilize a 50 ohm pulldown resistor to -2V; the output is also loaded with one ECL 100K gate.

OPERATING SPECIFICATIONS

*Supply voltage: ................. -4.5 + 5% to Vee
Supply current: .................. 80 mA typical

Logic 1 Input at 25°C:
     Voltage ..................... -1.165V min.
     Current ..................... 350 uA max.
Logic 0 Input at 25°C:
     Voltage ..................... -1.475V max.
     Current ..................... 0.5 uA min.
Logic 1 Output at 25°C: .......... -1.025V min.
Logic 0 Output at 25°C: .......... -1.620V max.
Operating temperature range: ..... 0 to +85°C
Storage temperature: ............. -55 to +125°C

*Output frequency will increase or decrease less than 1% for a respective increase or decrease of 5% in supply voltage.

PART NUMBER TABLE

Special modules can be readily manufactured to improve accuracies and/or provide customer specified random frequencies for specific applications.